Understanding Essential Plumbing Skills is Crucial for Installing a Bathtub
Understanding Essential Plumbing Skills is Crucial for Installing a Bathtub
Blog Article
This great article in the next paragraphs pertaining to How to Install a Bathtub Yourself is fairly motivating. You should investigate it.
Mounting a bathtub isn't exactly brain surgery, however it does call for strong plumbing, woodworking, as well as occasionally, tiling abilities. Replacing an old bathtub with a new one is additionally a moderately challenging task. If the old tub is conveniently accessible, the task can relocate quickly; if you need to open up a wall surface to remove the old bathtub and also place the brand-new bath tub, the task is much harder. In either case, the project is within a home handyman's abilities, although you will require an assistant to leave the old bathtub and also embeded in the new one. See to it you have qualified yourself for the task and are comfortable attempting it. As opposed to hiring a specialist to take control of a halfway-completed job, it is much better to think about using one before you start. Possibilities are you might need a professional plumber to make tube connections.
This post will certainly help you set up a new bath tub in your washroom if you have already acquired a brand-new tub as well as don't need to change the arrangement of your previous water pipelines.
Your tools and also material list must consist of the following:
Planning for the Setup
To start with, the sustaining frame provided with the bath needs to be fitted (if called for) according to the supplier's instructions. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is very important to ensure that if the tap comes with a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is also sensible to fit a sustaining plate under the taps system to stop pressure on the tub.
Fit the versatile tap ports to the bottom of the two taps utilizing 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and afterwards pass the outlet with the hole in the bath. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipeline to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bath must now be ready to be fitted in its last placement.
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your installation, after that the first thing you should do is separate the water system. After doing so, turn on the taps to drain any type of water continuing to be in the system. The process of removing the existing faucets can be rather troublesome as a result of the restricted accessibility that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipelines to the faucets. Have a towel prepared for the staying water that will originate from the pipes. When the supply pipes have been eliminated, utilize the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from transforming during this process. As soon as the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleansed of any kind of old securing substance.
Before going on to fit the new taps, compare the pipeline links on the old faucets to the new taps. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Setting up the Bath tub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wooden boards are helpful in evenly spreading out the weight of the bathtub over the area of the boards as opposed to focusing all the weight onto 4 tiny factors.
The following objective is to guarantee that the tub is leveled all round. This can be achieved by checking the level as well as readjusting the feet on the bath tub till the level reviews level.
To install taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipeline by making a compression join; then do the exact same for the various other tap.
Activate the supply of water and also inspect all joints and brand-new pipework for leakages and also tighten them if essential. Fill the bath tub as well as additionally examine the overflow outlet as well as the normal electrical outlet for leaks.
Ultimately, repair the bathroom paneling as defined in the maker's user's manual. Tiling and securing around the tub must wait until the tub has actually been utilized a minimum of when as this will settle it right into its final position.
Suitable New Taps
If the tails of the new taps are plastic, then you will require a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly require reducing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next, position the faucet in the mounting opening in the bath/basin ensuring that the washing machines remain in location in between the faucet as well as the sink. Secure the faucet in place with the manufacturer provided backnut. When the faucet is securely in place, the supply pipes can be linked to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with regular tap adapters. The previous type needs to be linked to the faucet finishes first, tightening up just by hand. The supply pipes can later on be connected to the other end. Tighten both ends with a spanner after both ends have been linked.
Tiling Around the Bath tub
In the area where the bath satisfies the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is essential as the fitting can move sufficient to break a rigid seal, creating the water to pass through the wall surface between the bathroom as well as the tiling, resulting in complications with wetness and also possible leakages to the ceiling listed below.
You can select from a range of coloured sealants to blend in your fixtures and also installations. They are sold in tubes as well as cartridges, as well as can securing spaces approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with spins of drenched paper or soft rope. Remember to constantly load the tub with water before sealing, to allow for the activity experienced when the bathtub is in use. The sealer can fracture relatively early if you do not consider this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are additionally quickly available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water-proof adhesive as well as cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I found that post on A Step-by-Step Guide to Installing a Bathtub when doing a lookup on the search engines. Appreciated our piece? Please share it. Help somebody else discover it. I love reading our article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.
For quick relief, contact! Report this page